How To Change Oil On Honda Vtx 1300 Motorcycle

How to Change Honda VTX Oil

by Chris Gilliland

Motorcycle Engine image by Andrew Breeden from Fotolia.com

As i of the about basic maintenance tasks demanded by a motorcycle, changing your motorcycle'southward oil is something motorcycle riders should be able to do themselves. Even though the various hoses and wires that surround a Honda VTX-series motorcycle may make the job announced complicated, changing the motor'south oil supply and its filter is simple enough to complete in less than half an hour.

Step ane

Wait under the motor to find both oil drain plugs; one is positioned beneath the forepart cylinder, while the second is positioned below the rear cylinder and slightly off to the left.

Step 2

Beginning the motor and let it idle in identify for 3 minutes to warm the oil. End the motor. Lift the motorcycle into an upright position. Place a cake of wood nether the kickstand, and so lean the motorcycle over so that the kickstand rests on the cake of wood.

Stride 3

Remove the drain plug from under the forepart of the motor using a 17-mm socket and a socket wrench. Grab the motor's oil in an oil pan. Clean the drain plug with a shop towel, and reinsert the plug into the motor using a torque wrench to tighten it to 29 foot pounds.

Step iv

Remove the drain plug from under the rear of the motor using a 17-mm socket and a socket wrench. Take hold of the motor's oil in an oil pan. Clean the bleed plug with a shop towel, and reinsert information technology into the motor using a torque wrench to tighten it to 29 human foot pounds.

Step 5

[Utilize an oil filter wrench](https://itstillruns.com/apply-oil-filter-wrench-7449698.html) to remove the oil filter from the lesser of the motor.

Step 6

Coat the new oil filter's sealing O-ring with 10W40 API SF motor oil. Screw the oil filter into place by hand until it is fitted snugly against the motor. Utilize a torque wrench to tighten the oil filter to twenty foot pounds.

Step 7

Remove the oil filler cap from the left side of the motor. Place a funnel into the motor's oil filler neck. Cascade up to 3.9 quarts of 10W40 API SF motor oil into the motor. Screw the filler cap dorsum on to the motor.

Remove the cake of wood from nether the kickstand and kickoff the motor. Check for oil leaks at the drain plugs and the oil filter, tightening them as needed to finish the leak. Stop the motor and wipe away any spilled oil with a shop towel.

References

• "The Professional Motorcycle Repair Program"; Professional Career Development Constitute; 1995
• "Honda VTX1800C Service Manual 2002-2003": Honda Motor Co.; 2003
• "Honda VTX1300S Service Transmission 2002-2003": Honda Motor Co.; 2003

Tips

• This process is the same for 1300cc and 1800cc VTX models.

Things You'll Need

• Block of forest
• 17-mm socket
• Socket wrench
• Oil pan
• Shop towels
• Torque wrench
• Oil filter wrench
• Funnel
• four quarts 10W40 API SF motor oil

Warnings

• Be certain to have the time to find both drain plugs on the lesser of the motor before y'all begin the process of changing your oil in society to go along from burning yourself unnecessarily.

Writer Bio

An avid motorcyclist, Chris Gilliland has immersed himself into the ii-wheeled world while balancing work life and raising three daughters. When he is not managing the parts section of a local, multi-line motorcycle dealership, Gilliland can often be found riding, writing or working on his motorcycle weblog, Wingman's Garage.

More Articles

How To Change Oil On Honda Vtx 1300 Motorcycle,

Source: https://itstillruns.com/change-honda-vtx-oil-7276561.html

Posted by: lindleyadind1979.blogspot.com

Share this post